How To Install Door Casing Without Nail Gun
We're finishing up a big dining room renovation, and I can't wait to prove you lot everything because I LOVE it!
One affair I have always wanted in my house was crown molding. I think it finishes a room and makes it look so much nicer! I thought it would exist actually expensive or difficult to install, or demand a ton of fancy tools, but it isn't.
With some patience, a few basic skills, and a few tools yous probably already accept, you can install crown molding yourself- without a fancy nailgun- and make information technology await professional- in a few hours!
This way does require a few extra steps (a nail gun would eliminate all the work I am detailing below, minus the caulking, but we couldn't go our hands on ane, and the piece of work around is really REALLY Like shooting fish in a barrel. I promise!).
Beginning off, you demand to measure your space, and buy molding. I went for unpainted (whats up major savings... I can paint myself for $5 less a yard!), and bought twice the amount I thought I needed. Which was super helpful unless you desire a zillion seams, because mess-ups happen. Both Domicile Depot and Lowes have a fabled selection of crown molding- both painted and unpainted.
First, I painted the trim with some killz to prime it. I then painted it with Clark & Kensington's "Antiquarian White" from Ace Hardware- that PERFECTLY matches our business firm's white- and since we need to repair our dining room ceiling anyways (significant repainting), I went for the aforementioned colour on the trim so information technology tin all be done at once.
I am into lazy solutions like that.
My dad then cut the molding for me since I am a tad awful at measuring. He cutting at an bending on our mitre saw- if you don't accept one, you could inquire the hardware store to pre-cutting for yous if you know your wall's measurements.
I could probably accept my dad write an entire book on cutting the crown molding- only instead I am going to direct you lot to this super helpful video nosotros found and used: http://www.youtube.com/watch?v=vPJCXTM810U. We did have ane seam in betwixt strips of molding per wall. The seams alloy in perfectly after you lot caulk and paint over them, so don't worry if you lot can't find a single strip of molding long plenty.
My dad really measured, cut, measured, cutting, and measured each strip again. Each piece took him almost iii-4 cuts to go it exactly perfect- but it is much better to cut a few times to get information technology right than to overcut. Take your time and measure carefully when cutting your molding, or you will accept a ton of seams and iv letter of the alphabet words!
Outset off by finding studs in your walls. And then hold upwardly the molding on your walls where y'all would like it to go and drill a hole through them into the studs. We were lucky that our walls had a stud running along the top of the wall, so we didn't take to worry likewise much nigh using the studfinder the whole time (what an awesome discovery THAT was!!).
Next, using long finishing nails, nail your trim in place (lined upward with the holes yous previously drilled). It is crucial to have someone hold the trim in place for you and proceed it taut with the wall- especially if yous have uneven ceilings (or walls) like I practise and then it is flush confronting them. You don't desire any gaping bits (if nosotros didnt sentinel, the molding would hands accept been crooked. A lot of new construction houses take uneven ceilings!)
Don't smash all the way in- but into the stud plenty so the trim tin can hang, unsupported. You dont want to come too shut with your hammer or yous could nail, nick r ding your beautiful molding!
You'll take hold of your finishing tool next (they are like under $5 at hardware stores- be sure to grab one with a tip that is larger than your nail heads, or it will be harder to control. Hold the finishing tool in ane hand, and line information technology up with your boom. With your other hand, hammer the end of the finishing tool to drive your nail into the trim- nick free.
Using spackling compound or forest putty, smooth over the nails completely.
Caulk along the superlative and lesser of the molding. If you don't want to repaint the wall or ceiling, tape off the area you dont want caulked. You'll notice we merely taped off under the molding since we have massive gaping holes in our ceiling and are going to take to repaint information technology all anyways when that gets fixed.
Let the spackle/forest putty and molding dry, and remove record.
When the putty is totally dry, usually overnight, utilize a fine sanding cake or piece of sanding paper, get over the putty and make it completely smooth with the molding.
Paint over the putty areas, and you are done!
How piece of cake was that? It might seem similar a few steps, but it actually isn't much work in one case you have the molding cutting. Where would you nearly like to add crown molding?
Reader Interactions
Trackbacks
Source: https://sweetcsdesigns.com/install-crown-molding-without-a-nailgun/
Posted by: zamoradrecandlere1979.blogspot.com
0 Response to "How To Install Door Casing Without Nail Gun"
Post a Comment